Hardware Requirements
The hardware required for creating a USB Rubber Ducky from an Arduino Nano is relatively inexpensive and can be sourced for under 20. The core components of the device are two 3.6V 0.5W zener diodes, a USB cable (type A to micro USB type B), a breadboard and some jumper wires. It is important to note that zener diodes with a wattage higher than 0.5W will not work.
Software Requirements
The software required to create the USB Rubber Ducky is free and can be downloaded from the internet. The software is used to program the Arduino Nano and allows the user to create scripts that will be sent to the computer when the device is plugged in.
Creating the Circuit
Once the required hardware and software have been sourced, the circuit can be created. The circuit should be connected as follows: the two zener diodes should be connected in series with the USB cable, with one end of the cable connected to the breadboard. The other end of the cable should be connected to the Arduino Nano. The jumper wires should then be connected from the zener diodes to the Arduino Nano.
Programming the Arduino Nano
Once the circuit has been created, the Arduino Nano can be programmed using the software. The user can create scripts that will be sent to the computer when the device is plugged in. The scripts can be used to perform a variety of tasks, such as opening a notepad and typing a message, or shutting down the computer.
Testing the Device
Once the device has been programmed, it can be tested by plugging it into a computer or an Android mobile phone. When the button is pressed, the script will be sent to the computer or mobile phone and the desired action will be performed.
Now open the Arduino IDE and select the board. Now, go to the file and open the file. Now, click on the upload button and wait for the upload to complete. Now, the board is ready to use.
Components Needed
The main component of this project is an Arduino Nano, as well as a few other components such as a 60 to 68 ohm resistor and a 2.2k ohm resistor. Additionally, a USB cable is also required.
Creating the Circuit
The circuit can be created either by making a simple PCB circuit or by taping the components together. However, it is not recommended to use the latter option as it can lead to a loose circuit. To create the circuit without a PCB or breadboard, the components should be connected in the following manner: the red 5V wire from the USB cable should be connected to the Arduino pin, the white T-minus wire should be connected to the junction, the green T wire should be connected to the junction, and the black wire should be connected to the ground junction.
Software Setup
The software setup involves downloading a zip file from a link, extracting it, and then opening the Arduino IDE. The board should then be selected and the file opened. After clicking the upload button, the board will be ready to use.
Installing the ID 1.0.3
In order to make a USB Rubber Ducky from Arduino Nano, it is essential to install ID 1.0.3 or any version under 1.0.6. This is the only version that will compile the code. After downloading the folder, it is necessary to open it and copy the USB Keyboard Library to the ordinal Library folder. This ensures that the project is completed properly.
Programming the Arduino Nano
The programming of the Arduino Nano requires the inclusion of the Key Helper.h Library. This is already included in the folder that has been copied. The update function must be placed in the main Loop. This is essential for the sketch to work. There are two functions that must be used. The press function is for pressing a key, such as ‘mod’ or ‘enter’. The type function is for typing a string. The remaining programming guide is provided in the zip file. If everything is done correctly, the code will compile and can be uploaded to the Arduino Nano.
Wiring the Arduino Nano
The wiring of the Arduino Nano is relatively simple. It requires connecting the Arduino Nano to the computer via a USB cable. The other end of the cable must be connected to the USB Rubber Ducky. This allows the Arduino Nano to send data to the USB Rubber Ducky.
Testing the USB Rubber Ducky
Once the Arduino Nano has been programmed and wired, it is time to test the USB Rubber Ducky. This is done by running the code on the Arduino Nano. If the code runs correctly, the USB Rubber Ducky should be able to send data to the computer. This can be tested by typing in a command and seeing if it is executed correctly. If the command is executed correctly, the USB Rubber Ducky is working properly.
It is a very simple and easy process.
Overview
Creating a USB Rubber Ducky from an Arduino Nano is a relatively straightforward process. It requires minimal materials and can be completed in a short amount of time. This guide will walk you through the steps necessary to create a functional USB Rubber Ducky from an Arduino Nano.
Materials
The materials required for this project are quite simple. You will need an Arduino Nano, a USB cable, and a few other components. The components required are:
Arduino Nano
USB cable
Breadboard
Jumper wires
Resistors
Capacitors
Assembly
Once you have all the necessary components, you can begin the assembly process. Begin by connecting the Arduino Nano to the breadboard using the jumper wires. Then, connect the USB cable to the Arduino Nano. Next, connect the resistors and capacitors to the breadboard. Finally, connect the USB cable to a computer.
Programming
Once the assembly is complete, you can begin programming the Arduino Nano. First, download the Arduino IDE and install it on your computer. Then, open the IDE and create a new sketch. Copy and paste the code for the USB Rubber Ducky into the sketch. Finally, upload the sketch to the Arduino Nano.
Testing
Once the programming is complete, you can test the USB Rubber Ducky. Plug the USB cable into a computer and the USB Rubber Ducky should be detected. You can then test the USB Rubber Ducky by typing commands into the computer. If the commands are executed correctly, then the USB Rubber Ducky is functioning properly.
Creating a USB Rubber Ducky from an Arduino Nano is a relatively simple process. It requires the main component of an Arduino Nano, as well as a few other components such as a 60 to 68 ohm resistor and a 2.2k ohm resistor, and a USB cable. The circuit can be created either by making a simple PCB circuit or by taping the components together. The software setup involves downloading a zip file from a link, extracting it, and then opening the Arduino IDE. After clicking the upload button, the board will be ready to use.
Making a USB Rubber Ducky from an Arduino Nano is a relatively simple process. All that is required is to install the ID 1.0.3, program the Arduino Nano, wire the Arduino Nano, and test the USB Rubber Ducky. If all of these steps are followed correctly, the USB Rubber Ducky should be able to send data to the computer.
Creating a USB Rubber Ducky from an Arduino Nano is a relatively simple process. With minimal materials and a few steps, you can create a functional USB Rubber Ducky. This guide has walked you through the steps necessary to create a USB Rubber Ducky from an Arduino Nano.